3D · Drag to turn
TERMINUSWatch dock
A charging dock for the Apple Watch, built from TERMINUS blocks on one black pole. The cap nut has grown into a crown that holds the round Apple Watch charger; the cable runs down the Spine at the back, out of sight.
The Apple Watch charger is not included.
Crown version only.
The plate, the pole and the ring, in one colour.
- Crown
- 80 x 80 x 151 mm
- Pebble
- 72 x 72 x 79 mm
- Charger pocket
- 28 mm across, 7 mm deep
- Charger
- Not included
- Cable
- In the Spine, out at the back
- Material
- PLA, matte stone texture
- Edition
- Numbered, under the block
- Made
- To order, in Germany
The lock becomes the charger.
Terminus was the Roman god of boundary stones. On the TERMINUS bookend the Cobalt cap nut locks the blocks to the pole. On the watch dock it has grown into a crown, and the round Apple Watch charger sits in it.
The Spine, the line down the back of every TERMINUS block, finally has a job: the cable runs down it, from the crown to the desk, out of sight.
Crown first, charger last.
- Stand the black plate on the desk, the pole up. The groove marks the back.
- Slide the lower block down the pole, its Spine channel over the groove.
- Crown: add the ring and the Small block, Spine at the back.
- Screw the crown on by hand until it stops, its notch over the Spine.
- Put the charger in the pocket and lay the cable down the Spine into the groove.
- Lay the watch on the charger, face up. The band hangs over the block.
What you choose
- Version. Crown: a Large and a Small block with a floating ring between them, 151 mm high. Pebble: one Medium block, 79 mm high, bedside size.
- Block. The lower block.
- Top block. The Small block on Crown. Pebble has no top block.
- Pole. The plate under the dock, the pole and, on Crown, the floating ring. They are one colour.
- Crown. Cobalt, as the cap nut on every TERMINUS, or any colour from the list.
Size and fit
- Crown 80 x 80 x 151 mm. Pebble 72 x 72 x 79 mm.
- The charger pocket in the crown is 28 mm across and 7 mm deep, for the round Apple Watch magnetic charger. The charger is not included.
- The cable runs in a 6 mm channel down the back of every block and leaves through a groove in the plate.
- The watch lies on the crown, face up. Any band works: it hangs over the block below.
- Every dock is made to order in our studio in Germany and carries its own number, under the lower block.
Putting it together
- Stand the black plate on the desk, the pole up. The groove in the plate marks the back.
- Slide the lower block down the pole, its Spine channel over the groove. Crown: then the ring and the Small block, Spine at the back.
- Screw the crown on by hand until it stops. It always stops with its notch at the back, over the Spine.
- Only then put the charger in the pocket and lay its cable down the notch and the Spine into the groove. Charger last, so the cable never winds up.
No tools and no glue. Everything comes apart again.
Material and care
- The blocks are PLA with a matte stone texture on the sides. Their top faces are printed face down, so they have an even, fine texture without print lines. The plate and pole are smooth.
- Dust with a dry, soft cloth. No water, no cleaning agents.
- Keep away from heat: no radiator, no direct summer sun, no hot car.
Safety
- Use only the Apple charger and its cable. Do not cover the charger while it is charging.
- Not a toy. Small parts before assembly. Keep away from small children and pets.
Maker
Kay Galerie, Poststrasse 12, 88677 Markdorf, Germany. info@kaygalerie.com
Apple Watch is a trademark of Apple Inc. Kay Galerie is not connected with Apple.